Filters
Filters (3 applied)
Clear All-
type (2)
-
has sound (1)
-
has video (1)
-
Conflict (4)
-
related places (4)
Collection
152 Results
-
HMAS Brisbane : Engine Room : Gauge board valve body
Technology
Maker: Unknown
The gauge board valve body is a circular, grey metal unit. On the front of the valve is a brass indicator panel. At the top of the panel is engraved SHUT, while at the bottom of the panel is engraved ...REL32981.041
-
HMAS Brisbane : Engine Room : Gauge from Engine Board
Technology
Maker: Unknown Weksler Instruments
The gauge is circular, with a machined alloy body and a grey rim. The face is white and is protected by an acrylic Perspex disc. It is calibrated from 0-1000 and has a red line indicator at 350. Nomen...REL32981.006
-
HMAS Brisbane : Engine Room : Light and Warning Sign
Technology
Maker: Unknown
The fluorescent light has a rectangular pressed metal case. On the upper surface are six screws and two large bolts (fitted). On the lower surface there are two cover sections at the ends, and in the ...REL32981.004
-
HMAS Brisbane : Engine Room : Salinity Indicator
Technology
Maker: Marine Electric Corporation Unknown
The salinity indicator consists of a rectangular steel case. At the rear, four attachment brackets have been cut. A rectangular access panel was mounted on the bottom (missing). The cover is hinged on...REL32981.028
-
HMAS Brisbane : Engine Room : Status Board No.1 Engine room
Technology
Maker: Unknown
The status board is located in the HMAS Brisbane Engine Room. The board is made up of a rectangular piece of wood, covered with a rectangular piece of white plastic, which is glued to the front. On th...REL32981.001
-
HMAS Brisbane : Engine Room : Switch unit
Technology
Maker: Palmer Unknown
The brass switch consists of a pressed metal case with a single attachment bracket welded to the back and drilled for two bolt holes. There are two cable fittings in the side of the case. The face is ...REL32981.031
-
HMAS Brisbane : Engine Room : Tartar Missile Launch Magazine Plate
Technology
Maker: Unknown
The tarter missile launch plate is a rectangular alloy plate with printed instructions for procedures that should be followed in case of Harpoon Fuel Leakage. It also contains instructions for recomme...REL32981.008
-
HMAS Brisbane : Fencing and Cabling missile launch cap
Technology
Maker: Unknown
The fencing and cabling is made up of four 1420mm long and three 1115mm long grey metal poles. The poles are 50mm in diameter. Each pole is secured to a metal bracket at its base which is then bolted ...REL33076
-
HMAS Brisbane : Fire Extinguisher holder
Technology
Maker: Unknown
The fire extinguisher holder is rectangular at the back with angles sides and base. It is made of metal and painted red. It has a black belt with buckle connected to the left hand side, which is used ...REL32993
-
HMAS Brisbane : Foot switch
Technology
Maker: Unknown
Foot switch, made of metal, painted grey. The switchl is rectangular at the back and rounded at the front. The top section of the foot switchl is grooved for better grip. A power cable protrudes from ...REL32990
-
HMAS Brisbane : Frame
Technology
Maker: Unknown
This frame is intended to be used with the Gun Plot Room door, but was collected from elsewhere in the ship. The door frame consists of a heavy L channel which is welded to the wall section. On the ch...REL32980.100
-
HMAS Brisbane : Gun Cleaning Brush (section of)
Technology
Maker: Unknown
The gun cleaning brush consists of a heavy alloy rod with a 10cm wide band of radial bristles. The centre of the rod is pierced and is fitted at each end with a section of threaded metal rod, projecti...REL32986
-
HMAS Brisbane : Gun Plot Room : Air Duct inspection cover and adjacent tally plate and bracket.
Technology
Maker: Unknown
The air duct inspection cover is a disc shaped assembly, fabricated from sheet alloy, with stamped sections welded as required and a central steel attachment point. The associated bracket/latch is a s...REL32980.021
-
HMAS Brisbane : Gun Plot Room : Air Filter
Technology
Maker: Unknown
The air filter is rectangular sheet metal case. The lid is made of L shaped channel and wire mesh and is retained by four screws. On the rear of the case is a circular hole with four screw holes and a...REL32980.048
-
HMAS Brisbane : Gun Plot Room : Aluminium cover
Technology
Maker: Unknown
The cover is a rectangular alloy sheet with two folded edges, located on one long side and one short side. On the opposite long side the edge is pierced by three holes, a length of rope with taped end...REL32980.095
-
HMAS Brisbane : Gun Plot Room : Aluminium cover
Technology
Maker: Unknown
The cover is a rectangular alloy sheet with two folded edges located on one long side and one short side. On the opposite long side the edge is pierced by three holes, a length of rope with taped ends...REL32980.096
-
HMAS Brisbane : Gun Plot Room : Aluminium floor plate
Technology
Maker: Unknown
Rectangular alloy plate with a cut-out section on one corner. The panel has two irregular holes cut together with two drilled holes. This is believed to be a sample of floor panelling from the GPR. Th...REL32980.086
-
HMAS Brisbane : Gun Plot Room : Amplifier Mk 76 Mod 8,
Technology
Maker: Unknown
The Amplifier Mk 76 Mod 8 consists of 2 rectangular consoles placed side-by-side. This is console 1 of 2. The console consists of two cabinets, divided into top and bottom sections. On the top section...REL32980.006
-
HMAS Brisbane : Gun Plot Room : Amplifier Mk 76 Mod 8,
Technology
Maker: Unknown
The Amplifier Mk 76 Mod 8 consists of 2 rectangular consoles placed side-by-side. This is console 2 of 2. The console consists of two cabinets, divided into top and bottom sections. On the top section...REL32980.007
-
HMAS Brisbane : Gun Plot Room : Bookshelf
Technology
Maker: Unknown
The shelf is constructed as an open-topped rectangular metal box. On the inside rear wall is a U channel for fitting a shelf divider. On the front face the end walls have folded edges and are about 1/...REL32980.088